GE8152 - Engineering Graphics - Introduction

70 flashcards · Other · by Premkumar Sampathkumar

1. How many battens will be there for a Drawing board? a) 1 b) 2 c) 3 d) 4

   2

2. The part that doesn’t belong to T-square is __________ a) Working edge b) Blade c) Stock d) Ebony

   Ebony

3. The angle which we can’t make using a single Set-square is ________ a) 45o b) 60o c) 30o d) 75o

   75o

4. The angle which we can’t make using both the Set-squares is _____________ a) 15o b) 105o c) 165o d) 125o

   125o

5. Small bow compass can draw circles less than _____ mm radius. a) 25mm b) 30mm c) 35mm d) 40mm

   25mm

6. Which is not the use of divider? a) To divide curved or straight lines into the desired number of equal parts b) To draw circles c) To transfer dimensions from one part of the drawing to another part d) To set-off given distances from the scale to the drawing

   To draw circles

7. The cardboard scales are available in a set of _______ scales. a) six b) ten c) eight d) twelve

   Eight

8. _________ is used to draw curves which are not circular. a) Compass b) Protractor c) French curves d) Pro circle

   French curves

9. The areas of the two subsequent sizes of drawing sheet are in the ratio ____ a) 1:5 b) 1:4 c) 1:2 d) 1:10

   1:2

10. The sizes from A0 to A5 increases. a) True b) False

    False

11. The increase in hardness is shown by the value of the figure put in front of the letter H, 2H, 3H, and 4H etc. a) True b) False

    True

12. What is the next size of 210 mm x 297 mm in drawing papers? a) 148 mm x 210 mm b) 297 mm x 420 mm c) 420 mm x 594 mm d) 105 mm x 148 mm

    297 mm x 420 mm

13. The Grade becomes ______ according to the figure placed in front of the letter B, 2B, 3B, 4B etc. a) harder b) lighter c) darker d) softer

    Softer

14. The accuracy of the drawing depends on the quality of the instruments used. a) True b) False

    True

15. Which of the following instrument is made of thin strips of wood arranged in a line to form a rectangle and on which, the drawing is made? a) Mini – drafter b) Drawing Board c) Protractor d) Scale

    Drawing Board

16. Which of the following tools is used to draw horizontal lines? a) Mini – drafter b) Protractor c) T – square d) French curve

    T – square

17. Which of the following instrument can be used to draw accurate perpendicular lines, parallel lines and angular lines? a) Mini – drafter b) T – square c) Protractor d) Set square

    Mini – drafter

18. According to the Indian Standard Institute (ISI), which among the following designation has the size 1000 x 700 (in mm)? a) B0 b) B1 c) B2 d) B3

    B1

19. Which is the most common tool used for drawing circles? a) French curve b) Mini – drafter c) Divider d) Compass

    Compass

20. For drawing circles with a large radius, which of the following tool is used? a) Bow compass b) Lengthening bar compass c) Divider d) Protractors

    Lengthening bar compass

21. Which of the following drawing tools is used by architects for making blueprints? a) Drawing Pencils b) Dusters c) Ink Pen d) Erasers

    Ink Pen

22. Which of the following drawing tool is not used to set the drawing sheet onto the drawing board? a) Drawing clips b) Drawing pins c) Divider d) Adhesive Tape

    Divider

23. According to the Indian Standard Institution (ISI), what is the size of the designation A3 in mm? a) 420 x 297 b) 841 x 594 c) 1189 x 841 d) 297 x 210

    420 x 297

24. Which of the following drawing tool is used to transfer dimensions when there is a repetition of the dimensions? a) Compass b) Protractor c) Divider d) Mini – Drafter

    Divider

25. Which of the following grades of leads is the hardest? a) 6B b) 5H c) 4B d) 6H

    6H

26. For marking angles, which of the following drawing tool is used? a) Protractor b) Divider c) Compass d) French curve

    Protractor

27. Using 30˚ – 60˚ – 90˚ and 45˚ – 45˚ – 90˚ set squares, which of the following angle is not possible to draw? a) 45˚ b) 30˚ c) 10˚ d) 90˚

    10˚

28. Which is the instrument used to draw parallel lines fast? a) Set square b) Ruler scale c) Protractor d) Roll-n-draw

    Roll-n-draw

29. The preferred size of the drawing sheets is recommended by the ______ a) B.I.S b) ASME c) ASTM d) NIST

    B.I.S

30. __________ is not an essential thing for free-hand sketching. a) A soft-grade pencil b) French curves c) A soft rubber-eraser d) A paper in form of a sketch-book or a pad

    French curves

31. Medium thickness, line-group of 2mm are not used for _________ a) out lines b) dotted lines c) cutting plane -lines d) dimension lines

    Dimension lines

32. The line given below is used for__________ a) Long-break line b) Cutting planes c) Centroidal lines d) Out lines of adjacent parts

    Long-break line

33. The line given below is used for_________ a) Hidden outlines b) Cutting planes c) Hidden edges d) Dimension lines

    Cutting planes

34. Dashed thick (wide) line is represented by ____________ a) b) c) d)

35. Match the following. a) 1, i; 2, ii; 3, iii; 4, iv b) 1, ii; 2, iii; 3, i; 4, iv c) 1, ii; 2, iv; 3, iii; 4, i d) 1, iv; 2, iii; 3, ii; 4, i

    1, ii; 2, iii; 3, i; 4, iv

36. Match the following. a) 1, i; 2, ii; 3, iii; 4, iv b) 1, ii; 2, iii; 3, iv; 4, i c) 1, ii; 2, iv; 3, iii; 4, i d) 1, iv; 2, iii; 3, ii; 4, i

    1, ii; 2, iii; 3, iv; 4, i

37. Drawing pencils are graded according to increase in relative __________ a) diameter b) sharpness c) length d) hardness

    Hardness

38. Match the following. 1. Dimension lines - i.Continuous thick lines 2. Extension or Projection lines - ii.Continuous thin lines 3. Margin lines - iii.Continuous thick lines 4. Outlines - iv.Continuous thin lines a)1, i; 2, ii; 3, iii; 4, iv b) 1, ii; 2, iii; 3, iv; 4, i c) 1, ii; 2, iv; 3, iii; 4, i d) 1, iv; 2, iii; 3, ii; 4, i

    1, ii; 2, iv; 3, iii; 4, i

39. In engineering drawing, which type of line indicates that there is a change of plane? a) Continuous thin wavy b) Long chain thin c) Continuous thick d) Medium thick short dashes

    Continuous thick

40. Which of the following lines are used to show that the object is cut and then viewed? a) Hidden lines b) Leader lines c) Centre lines d) Hatching Lines

    Hatching Lines

41. What do hidden lines in orthographic projections denote? a) Holes or slots b) Change of Plane c) Position of cut d) Centre of a circle or cylinder

    Holes or slots

42. From the below figure, what is the name of the line X? a) Outline b) Section line c) Hidden line d) Hatching

    Hidden line

43. What is the type of line used for line a? a) Continuous thick b) Continuous thin straight c) Medium thick short dashes d) Continuous thin wavy

    Continuous thin straight

44. The axis of the cylinder or sphere is denoted by which of the following line? a) Section line b) Centre line c) Hidden line d) Leader line

    Centre line

45. The ratio of height to length of an arrow in dimensioning is ___ a) 1:2 b) 1:3 c) 1:4 d) 1:1.5

    1:3

46. What is the length of the short dashes of the center lines? a) 5mm b) 2mm c) 1mm d) 3mm

    2mm

47. Among the following, which of the representation is wrong? a) b) c) d)

48. Which type of line is used to join the dimension line and the curve that needs to be dimensioned? a) Leader line b) Outline c) Dimension line d) Section line

    Leader line

49. What is the difference between the section line and the center line? a) The length of the long dashes b) The length of short dashes c) The width of the gap d) The two ends of the lines

    The two ends of the lines

50. In dimensioning, the lines enclosing the dimension line are known as ____ a) Leader line b) Dimension line c) Extension line d) Outline

    Extension line

51. Dimensioning doesn’t represent _____ a) height b) length c) depth d) material

    Material

52. Which is the wrong statement regarding dimensions? a) Every dimension must be given, but none should be given more than once b) Every dimension should be written to the left side of the drawing c) Dimensions should be placed outside the views d) A center line should not be used as a dimension line

    Every dimension should be written to the left side of the drawing

53. Dimension lines should be drawn at least ________mm away from the outlines and from each other. a) 5 b) 6 c) 7 d) 8

    7

54. Two types of dimensions needed on a drawing are: i) size or functional dimensions and ii) location or datum dimensions. a) True b) False

    True

55. An outline or a center line should be used as a dimension line. a) True b) False

    False

56. Which is the wrong statement from the below options? a) As far as possible all dimensions should be given in millimeters, omitting the abbreviation mm b) The height of the dimension figures should be from 3mm to 5mm c) A zero must always precede the decimal point when the dimension is less than unity d) The dimensions should only be given in mm

    The dimensions should only be given in mm

57. In chain dimension, the dimensions are arranged parallel to each other. a) True b) False

    False

58. In the combined dimension, the dimensions are arranged in a straight line only. a) True b) False

    False

59. In which of the following type of dimensioning, the dimensions are arranged only in a straight line? a) Parallel dimension b) Chain Dimension c) Combined dimension d) Aligned dimension

    Chain Dimension

60. Which type of dimensioning is shown in the figure? a) Parallel dimension b) Unidirectional dimension c) Combined dimension d) Chain Dimension

    Parallel dimension

61. Which type of dimensioning is shown below? a) Chain dimension b) Parallel dimension c) Unidirectional dimension d) Combined dimension

    Chain dimension

62. Identify the ‘a’ in the given picture a) dimension line b) hidden line c) center line d) outline

    Center line

63. Identify the ‘a’ in the below given picture. a) dimension line b) outline c) leader d) extension line

    Extension line

64. While representing the diameter in dimensioning it is represented as __________ a) D b) Ø c) Dia d) d

    Ø

65. 1. From below given figure, match the following. a) a, i; b, ii; d, iii; e, iv b) a, iv; b, iii; d, ii; e, i c) a, i; b, iv; d, iii; e, ii d) a, iii; b, ii; d, i; e, iv

    a, iv; b, iii; d, ii; e, i

66. Identify the note in the below given figure. a) A b) B c) C d) D

    B

67. Which of the lines is a thin continuous line with the ends terminating in arrowheads and is enclosed by extension lines, outlines or center lines? a) Dimension line b) Leader line c) Extension line d) Section line

    Dimension line

68. What is the name of the thin continuous line which encloses the dimension lines are generally drawn 1mm away from the outlines? a) Dimension line b) Section line c) Leader line d) Extension line

    Extension line

69. Which of the following dimension needs to be calculated? a) Length of the rectangle b) Breadth of the rectangle c) Diameter of circle d) Position of circle

    Diameter of circle

70. While dimensioning a feature with a square cross-section, what should be added before the dimension figure? a) SQUARE b) SQ c) Sq d) Nothing

    SQ